Leader

Collapse

Announcement

Collapse
No announcement yet.

A SERIOUS INTERRUPTION

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • A SERIOUS INTERRUPTION

    By Chief Craig C. Clarke
    KARNAC.com
    Safety Editor


    One of the most dangerous conditions for a race car driver besides fire, is a stuck throttle or an engine run-away condition. In the past, the driver did not have any option but to hang on and try and stop the car by slamming on the brakes or attempting to kill the ignition. Reaching for the power switch in a panic situation is not an easy thing to do; Not to mention if the throttle linkage becomes jammed, stuck or broken. Now, this situation can me managed automatically with the introduction of the ROUSH IGNITION INTERRUPTER SYSTEM. This is a multi-component system that reacts to the vehicle and driver when the throttle linkage breaks or sticks, and positively disables the ignition system on the vehicle. In a recent personal interview at a race with Roush spokesman Robert Corn, he described the various components and their actions.


    1. INTAKE MANIFOLD VACUUM SWITCH:
    This is a pressure switch that is installed in the intake manifold, and works off the principal that the throttled engine’s power is proportional to the vacuum in the intake manifold. The Roush system is set so that the switch closes just before full power is achieved. It is recommended that this switch be screwed directly into the intake manifold spacer under the carburetor. This switch has a 1/8” NPT male thread on it for this purpose. This switch is normally closed and will open with vacuum. It is set to go closed when exposed to falling vacuum. For Winston Cup, Busch Restricted and Super Truck vehicles, the vacuum set point is 4”Hg falling vacuum. For Busch Open engines, the vacuum set point is 6”Hg falling vacuum.

    2. BRAKE LINE PRESSURE SWITCH:
    The brake line pressure switch is set into the front brake lines and set to close at a value that represents a high pedal effort such as in a panic brake situation. It is however, not set to activate under normal race braking situations. The preferred mounting location for this switch is in the junction block where the right and left front brake lines divide from the master cylinder front brake line feed. They suggest that this switch be securely attached to reinforce the mounting in the brake line block. This is a normally open switch that will close with 1100psi rising pressure.

    3. BRAKE PEDAL POSITION SWITCH:
    This is a travel indicator switch that is attached to the brake pedal and works as a backup to the Brake Line Pressure Switch. It activates the Roush Ignition Interrupter if the brake pedal linkage breaks and/or goes to the floor. Since every team and each car varies so much, they state that the individual team should develop their own mounting bracket for this particular switch. It is suggested that the mounting location for this travel switch should be to attach the switch arm to the brake pedal at the same point where the master cylinder push rod attaches to the pedal. The switch is self adjusting for stroke, so you need to be sure to make the pedal go through its complete travel. This should be done after the switch is mounted to the bracket. It is important to note that some vehicles have brake pedals that bottom out on the master cylinder. Therefore, the switch must be adjusted with the master cylinder push rod hooked up.

    4. CONTROL PANEL - IGNITION LATCHING CIRCUIT:
    This is a small profile control panel which consists of a red warning light, a 5 amp ATO fuse, and a momentary reset switch. Included in the system are two relays which provide a positive disconnect latching circuit which prevents any power flow to the ignition system of the vehicle until it has been manually reset from the control button mounted inside the car.

    This system was tested by race car drivers Jeff Burton & Ricky Rudd under NASCAR© supervision last season, and is the only device of this type currently approved by NASCAR© for all of their divisions. According to Robert Corn (Roush), The system can also be configured to all types of race cars, not just NASCAR©. How much is this great technology? Under $600.00 for the complete system. It’s approach is simplistic, and if it can save a driver from crashing into the wall due to a stuck throttle, it is well worth the price.

    Chief Craig C. Clarke
    TRACK RESCUE FIRE DEPARTMENT
    http://www.trackrescue.com
    “Safety for Racers”


    Sales Information: Jim Shockley - Michigan 734-779-7251
    Steve Loyd - North Carolina 704-632-1628

    Technical Info: Dan Ostrander - 313-294-8246

    Links to Articles: http://www.karnac.com/floridastocks/index.shtml
    http://www.roushracing.com/jack_roush/archive.asp


    ©KARNAC.com & Craig C. Clarke, ALL RIGHTS RESERVED


300x600 Ad Unit (In-View)

Collapse

Upper 300x250

Collapse

Taboola

Collapse

Leader

Collapse
Working...
X